收藏本站
71M6533- DB Demo Board User’s Manual
2.2.2 CALIBRATION PROCEDURE WITH FIVE MEASUREMENTS
Each phase is calibrated individually. The calibration procedure is as follows:
1)
2)
3)
4)
5)
6)
7)
8)
9)
The calibration factors for all phases are reset to their default values, i.e. CAL_In = CAL_Vn = 16384,
and PHADJ_n = 0.
An RMS voltage V ideal consistent with the meter’s nominal voltage is applied, and the RMS reading
V actual of the meter is recorded. The voltage reading error Axv is determined as
Axv = (V actual - V ideal ) / V ideal
Apply the nominal load current at phase angles 0°, 60°, 180° and – 60° (-300°). Measure the Wh
energy each time and record the errors E 0 , E 60 , E 180 , and E 300 .
Calculate the new calibration factors CAL_In , CAL_Vn, and PHADJ_n , using the formulae presented
in section 2.1.2 or using the spreadsheet presented in section 2.2.4.
Apply the new calibration factors CAL_In , CAL_Vn , and PHADJ_n to the meter. The memory
locations for these factors are given in section 1.9.1.
Test the meter at nominal current and, if desired, at lower and higher currents and various phase
angles to confirm the desired accuracy.
Store the new calibration factors CAL_In , CAL_Vn , and PHADJ_n in the EEPROM memory of the
meter. If a Demo Board is calibrated, the methods involving the command line interface shown in
sections 1.9.3 and 1.9.4 can be used.
Repeat the steps 1 through 7 for each phase.
For added temperature compensation, read the value TEMP_RAW (CE RAM) and write it to
TEMP_NOM (CE RAM). If Demo Code 4.6n or later is used, this will automatically calculate the
correction coefficients PPMC and PPMC2 from the nominal temperature and from the characterization
data contained in the on-chip fuses.
Tip: Step 2 and the energy measurement at 0° of step 3 can be combined into one step.
2.2.3 CALIBRATION PROCEDURE FOR ROGOWSKI COIL SENSORS
Demo Code containing CE code that is compatible with Rogowski coils is available from MAXIM INTEGRADED
PRODUCTS.
Rogowski coils generate a signal that is the derivative of the current. The CE code implemented in the
Rogowski CE image digitally compensates for this effect and has the usual gain and phase calibration
adjustments. Additionally, calibration adjustments are provided to eliminate voltage coupling from the sensor
input.
Current sensors built from Rogowski coils have a relatively high output impedance that is susceptible to
capacitive coupling from the large voltages present in the meter. The most dominant coupling is usually
capa citance between the primary of the coil and the coil’s output. This coupling adds a component proportional
to the derivative of voltage to the sensor output. This effect is compensated by the voltage coupling calibration
coefficients.
As with the CT proced ure, the calibration procedure for Rogowski sensors uses the meter’s display to calibrate
the voltage path and the pulse outputs to perform the remaining energy calibrations. The calibration procedure
must be done to each phase separately, making sure that the pulse generator is driven by the accumulated real
energy for just that phase. In other words, the pulse generator input should be set to WhA, WhB, or WhC,
depending on the phase being calibrated.
In preparation of the calibration, all calibration parameters are set to their default values. VMAX and IMAX are
set to reflect the system design parameters. WRATE and PULSE_SLOW , PULSE_FAST are adjusted to obtain the
desired Kh.
Page: 40 of 75
`
REV 3
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
71M6534H-DB BOARD DEMO 71M6534H
71M6541F-DB DEMO BOARD 71M6541F
71M6543F-DB-CT DEMO BOARD 71M6543F-DB-CT
72-CNV-5 CONVERTER RS-232 TO RS-422 5V
72346-001 72346-1-SCA-II REC
72347-001LF CONN RECEPT SCA2 20POS VERT PCB
72436-001LF 80POS EXT HT. REC SCA-2
72442-201LF CONN RECEPT SCA2 80POS VERT PCB
相关代理商/技术参数
71M6533G 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Exceeds IEC 62053/ANSI C12.20 Standards
71M6533G-IGTR/F 功能描述:计量片上系统 - SoC AC Power Monitoring SoC-Programd RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6533H 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Energy Meter IC
71M6533H-IEL 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Precision Energy Meter IC
71M6533H-IEL/F 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Precision Energy Meter IC
71M6533H-IELR 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Precision Energy Meter IC
71M6533H-IELR/F 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Precision Energy Meter IC
71M6533H-IGT/F 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel